|
Who's Online
There currently are 6022 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
The service was quick and simple, finding the service manual easy and it appears to be the original with colour schematics. It contained the info I was after and so sorted the problem.
I have copied it to CD and attached the envelope to the inside back cover of the owners manual. Good manual and excelent service. Robin Wood, Wood Electronics, New Zealand.
;
Exactly what was needed to assess the product - excellent value and great service
;
Nice to have the service manual for the Sony DCR-TRV345E now. The document is of excellent quality.
;
MACKIE HR824 26 pages English-only Service Manual contains:
1) HR824 technical overview with the description of front and rear panel switches.
2) HR824 specs
3) Block Diagram
4) Wiring Diagram
5) Packaging management
6) Spare part & final assembly list (for PCB rev A and B) + exploded view
7) Test Procedures (where, how to measure voltage...) including Test Point diagram on the PCB.
8) IC and Transistor charts.
Excellent guide: very clear, good scan quality enabling us to print readable diagram :-)
Note:
Mackie HR824 make extensive use of surface mount devices (SMD). Service on the HR824 must
only be undertaken by experienced service technicians with the right tools, experience and patience to perform surface mount rework when needed.
;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
GV 30�, GV 50�
Laufwerk
Fett (75988 061 7800) auf schattierte Flächen auftragen
30000
Flachbandleitung
22000 Stator 30000 21000 Rotor 11600 Massefeder 11500 Kohlestift 11000 Bandtrommel
Fig. 8.37 Fig. 8.35 8.13 A/W-Kopfeinheit (50200) � Schraube (Pos. 50210) lösen und A/W-Kopfeinheit (50200) gemä� Fig. 8.36 in Pfeilrichtung drücken und nach oben abnehmen. Hinweis: Loch U der A/W-Kopfeinheit (50200) nach der Position des Stiftes V auf dem Laufwerkchassis ausrichten. Anschlie�end den Bandlauf und die Trackinglage (X-Wert) einstellen (siehe Punkt 9. "Einstellungen").
50200 50210
11000
U
Y
10400
V
10400
Fig. 8.38 Achtung: Nach dem Einbau des Rotors (21000) muss die Phase des Kopfrads eingestellt werden. Die Löcher W des Kopfrads und X des Rotors müssen gemä� Fig. 8.39 auf der gleichen Seite liegen. Die Schrauben (30000) für den Rotor und den Stator (22000) mit einem Drehmoment von 2.5 bis 3.5kg/cm befestigen.
Fig. 8.36 8.14 Bandtrommel � 2 Schrauben (30000) herausdrehen, Stator (22000) abnehmen und Bandtrommelerdungsfeder (11600) entfernen (Fig. 8.37). � Dreht man jetzt das Laufwerk um, fällt der Kohlestift (11500) heraus (Fig. 8.37). � 2 Schrauben (30000) herausdrehen und Rotor des Motors (21000) entnehmen (Fig. 8.37). � 3 Schrauben (10400) auf der Unterseite des Laufwerks lösen und die Bandtrommel kpl. (11000) herausnehmen (Fig. 8.38). Einbau: Beim Einbau die Bandtrommel kpl. (11000) auf den beiden Passstiften Y der Montagefläche positionieren (Fig. 8.38). Die Schrauben (10400) mit einem Drehmoment von 3.9 bis 4.2kg/cm festziehen.
11200 Kopfrad
W
21000 Rotor
X
Fig. 8.39
GRUNDIG Service 5 - 13
|
|
|
> |
|